Dynabrade 13204 - Dynastraight

Dynabrade high quality Dynastraight finishing tool is ideal for the graining, cleaning, and polishing on stainless steel, aluminum, carbon steel and composites. This Dynastraight model has a threaded arbor (5/8″-11) that is ideal for use with the optional 94472 Dynacushion pneumatic wheel (sold separately). The optional 3″ wide pneumatic wheel uses 3 1/2″ x 15 1/2″ coated & non woven (surface conditioning) abrasive belts.

Dynabrade 13204 - Dynastraight

Category Brands: .

Dynastraight Air-Powered Abrasive Finishing Tool is designed for graining, cleaning and polishing on stainless steel, aluminum, carbon steel and composites. Dynastraight tools are designed to prepare, condition, finish, buff and polish on countless materials. For use with a variety of accessories and abrasives.

Features

  • Rear Exhaust
  • Motor HP (W): 0.7 (522)
  • Motor RPM: 3,400
  • Sound Level: 82 dB(A)
  • Max. Air Flow SCFM (L/Min): 35 (977)
  • Weight Pound (kg): 3.8 (1.7)
  • Length Inch (mm): 14-5/8 (371)
  • Height Inch (mm): 1-3/4 (44)

Storage & Handling

  1. Check tool speed regularly with a tachometer. If tool is operating at a higher speed than the RPM marked on the tool, the tool should be serviced to correct the cause before use.
  2. Some silencers on air tools may clog with use. Clean and replace as required.
  3. All Dynabrade Rotary Vane air motors should be lubricated. Dynabrade recommends one drop of air lube per minute for each 20 SCFM (example: if the tool specifications state 40 SCFM, set the drip rate of your filter-lubricator at 4 drops per minute). Dynabrade Air Lube (P/N 95842: 1 pt. 473 ml.) is recommended.
  4. An Air Line Filter-Regulator-Lubricator must be used with this air tool to maintain all warranties. Dynabrade recommends the following: 11405 Air Line FilterRegulator-Lubricator — Provides accurate air pressure regulation, two-stage filtration of water contaminants and micro-mist lubrication of pneumatic components. Operates 40 SCFM @ 100 PSIG has 3/8″ NPT female ports.
  5. Use only genuine Dynabrade replacement parts. To reorder replacement parts,please specify the Model #, Serial # and RPM of your machine.
  6. Grease the planetary gear assembly with the 95542 Grease by applying 2-3 plunges with the 95541 Grease Gun after every 50 hours of use for maximum gear life.
  7. A Motor Tune-Up Kit (P/N 96260) is available which includes assorted parts to help maintain motor in peak operating condition.
  8. Mineral spirits are recommended when cleaning the tool and parts. Do not clean tool or parts with any solvents or oils containing acids, esters, keytones, chlorinated hydrocarbons or nitro carbons.
  9. DO NOT clean or maintain air tools with chemicals that have a low flash point (example: WD-40®).

Installation

  1. With power source disconnected from tool, securely fasten abrasive/accessory on tool.
  2. Install air fitting into inlet bushing of tool. Important: Secure inlet bushing of tool with a wrench before attempting to install the air fitting to avoid damaging valve body housing.
  3. Connect power source to tool. Be careful not to depress throttle lever in the process.
  4. Check tool speed with tachometer. If tool is operating at a higher speed than the RPM marked on the tool or operating improperly, the tool should be serviced to correct the cause before use.
  5. Air tools are not intended for use in explosive atmospheres and are not insulated for contact with electrical power sources. Sanding/Grinding certain materials can create explosive dust. It is the employers responsibility to notify the user of acceptable dust levels. Sanding/Grinding can cause sparks which can cause fires or explosions. It is the users responsibility to make sure the work area is free of flammable materials.

TDS / MSDS

To request any type of technical sheet or safety sheet.

Product Categories

TDS / MSDS

To request any type of technical sheet or safety sheet.

Can't find the right product?

Talk to a Technical Representative

Need advice?

Our technical team can provide assistance on your industrial product or application needs. Please complete the enquiry form below and we will contact you within 24-48 hours.

Request a quote

Please send us your request to receive a customised offer, either for specific products or special requirements.

Technical Data sheet and safety data sheet

Please fill in the form to receive the .pdf document.